high head slurry pump is always important to get a good match between the system requirements and pump features NotIs it critical to pick a pump that meets your requirements for fiow capacity and head ratings , but it is alsoimportant to select the nght pump design .
Our high head slurry pump comes with only one impeller and allows slums to enter insidechamberone uction Side. it is a horizontal cantilever pump that is designed to handle your highpressure, high flow rate applications.2. Housed inside the double-casing design are wet-end parts made form abrasion resistant high-chromeDifferent types of impellers are designed to handle vaned flow pattems4. The rotating shaft utilizesgland sea. The expeller dynamic seal and other mechanical sealarrangements are among options.3. MH series light duty pump is designedat a high speed while delivering large capacity and owdischarge head. It is suitable for low-abrasion, low-viscosity slurry pumping applications.6. The discharge outlet has 8 positions at 45 degree intervals that caselected to meetInsta ationand application requirements
we are high head slurry pump manufacturers,if you want to buy high head slurry pump,pls contact us.
Main Specifications: Size: 1-30 inches Capacity: 25-13860 m3/h Head: 5-60m,we are LAP low abrisive slurry pump manufacturer,we can guarantee quality. Material: Hi-chromium metal liner, or Rubber liner Seal: Packing seal, Expeller seal
Applications: Series HAP slurry pumps are widely used in the mining, coal washing plant, power plant, metallurgy, petrochemical, building material, dredging and other industrial departments, etc. It is used in the various working sites including hydro cyclone feeding pump, magnetic separator feeding pump, underflow slurry pump (thickener underflow pump, filter separator underflow pump), flotation feeding pump, vibrating sieve feeding pump, shaking grading pressure pump, concentrate pump, and tailing pump.
Features: 1. This sump pump is with single pump casing, vertical cantilever designed; 2. To use double suction and open type impeller design, and the impeller could be high chrome alloy of rubber lined material;we are vertical sump slurry pump supplies,we can guarantee quality. 3. The bearing is used grease lubrication; 4. The clearance between the impeller and frame plate could be adjusted, to make sure our pump run in its highest efficient; 5. No need any shaft seals; 6. The pumps could be direct coupling drive or with belt drive by motor;
Working Applications: Series HHD slurry pumps are widely used in the mining, coal washing plant, power plant, metallurgy, petrochemical, building material, dredging and other industrial departments, etc. It is used in the various working sites including hydro cyclone feeding pump, magnetic separator feeding pump, underflow slurry pump (thickener underflow pump, filter separator underflow pump), flotation feeding pump, vibrating sieve feeding pump, shaking grading pressure pump, concentrate pump, and tailing pump. Designed for handling strong abrasive and high concentration slurries, HHD series slurry pumps are cantilevered heavy duty slurry pumps with metal liner. With thick wear parts and heavy-duty support, HHD series could run in series in the allowable range of pump working pressure.
1. Supplying the Exchangeable Pump Parts With the Warman Series Pumps 1) HAP series pump Volute liners, impellers, and suction liners under heat treatment; 2) Pump volute liners & impellers under machining work; 3) Pump parts under casting; 4) The Vanishing mold casting technology is adopting;
Main Specifications: Size: 65mm-300mm Capacity: 50-1800 m3/h Head: 50-90m Material: Hi-chromium metal liner, or Rubber liner Seal: Expeller seal combined with packing and Mechanical seal
Cost Advantage: (1) The efficiency of XS pumps are 2%~3% higher than the same type pumps due to adopting advanced hydraulic model and thus minimum the operating costs. (2) The NPSH of type XS pumps are 1-3 meters lower than the same type split pumps due to using advanced hydraulic model and advanced manufacturing technique and thus minimize the foundation costs and extending the using life. (3) Type XS pumps are suitable for any site working condition due to using SKF NSK bearing and other parts chosen by the customers and thus minimize the maintenance costs.
Pump Features: 1. Series of TL(R) FGD pump is a single-stage ,single-suction ,horizontal centrifugal pump .This series pump is matched by tight structure X bracket. It mainly used as the circulating pump for absorbent tower in FGD appliances. It has such features: wide rang flowing capacity ,with high efficiency, high saving power. 2. Bearing lubricating way: diluted oil 3. This kind of pump adopts back pull-out structure keeping it easy construction and easy maintenance. It does not need disassemble inlet & outlet pipeline.
注: 建议图片大小150px*50px
